In electrical systems, high temperatures normally indicate an impending trouble. This can result from unnecessarily high resistance, short circuits, poor connections, ground fault or any other failing components common with electrical equipment. The problem must be pinpointed and rectified early enough as complete failures are normally expensive and at times can results to catastrophes. Instead of struggling to find the incipient failures through visual and other manual inspection methods which are costly, time consuming and may not pinpoint the problem, engineers are now turning to electrical infrared inspection that has proved to be the most effective alternative.
It is a good practice to inspect all electrical system components twice a year or at least every 12 months at minimum. When properly conducted, it is possible to detect and prevent accidents well in advance before they occur. For the equipment and the control systems that are subjected to movements and vibrations, every six months inspection is not optional.
In normal distribution, infrared surveys should be conducted on annual basis and is considered part of a regular preventive and maintenance program. This form of testing makes it possible to inspect a large number of components within the shortest time possible locating the faulty items in the system that could not be located through the physical survey or testing.
The devices that requires infrared surveys are the bus ducts, the distribution center, the distribution panels, receptacle panel, the transformers, lighting system, switchgears, disconnects and other components that make up the system. If well done, the uninterruptable power supply can be achieved as there is no need to shut down the system. The process of inspection takes place under the normal load without any disturbance to normal supply.
Using the state of the art equipment deployed for scanning, thousands of components get inspected in a matter of hours with very accurate results. With very high rate of efficiency and effectiveness, most of engineers are now using this form of inspection. It cut down on staff needed for the job and increases profitability by a big margin. In fact, it has one to four returns on investment and as such, companies that hope to survive into the future have to adopt this technology.
With the endorsement and approval from the InterNational Electrical Testing Association and the National Fire Protection Association and other related regulatory authorities, it is a mistake to continue depending on the manual method of testing.
This form of testing and survey therefore saves engineers millions of dollars improving profitability and significantly decrease the expenses in the areas of operations, testing and maintenance in general. With this convenience and financial benefits, this is a technology you cannot afford to miss in this century if you think of remaining in business.
In order to fully benefit from this cutting edge technology, you must be very keen on the companies you choose for the job. At minimum, the prospective company must have some proven record of good job done on previous assignments. For a good choice, the level of experience of staff also matters.
It is a good practice to inspect all electrical system components twice a year or at least every 12 months at minimum. When properly conducted, it is possible to detect and prevent accidents well in advance before they occur. For the equipment and the control systems that are subjected to movements and vibrations, every six months inspection is not optional.
In normal distribution, infrared surveys should be conducted on annual basis and is considered part of a regular preventive and maintenance program. This form of testing makes it possible to inspect a large number of components within the shortest time possible locating the faulty items in the system that could not be located through the physical survey or testing.
The devices that requires infrared surveys are the bus ducts, the distribution center, the distribution panels, receptacle panel, the transformers, lighting system, switchgears, disconnects and other components that make up the system. If well done, the uninterruptable power supply can be achieved as there is no need to shut down the system. The process of inspection takes place under the normal load without any disturbance to normal supply.
Using the state of the art equipment deployed for scanning, thousands of components get inspected in a matter of hours with very accurate results. With very high rate of efficiency and effectiveness, most of engineers are now using this form of inspection. It cut down on staff needed for the job and increases profitability by a big margin. In fact, it has one to four returns on investment and as such, companies that hope to survive into the future have to adopt this technology.
With the endorsement and approval from the InterNational Electrical Testing Association and the National Fire Protection Association and other related regulatory authorities, it is a mistake to continue depending on the manual method of testing.
This form of testing and survey therefore saves engineers millions of dollars improving profitability and significantly decrease the expenses in the areas of operations, testing and maintenance in general. With this convenience and financial benefits, this is a technology you cannot afford to miss in this century if you think of remaining in business.
In order to fully benefit from this cutting edge technology, you must be very keen on the companies you choose for the job. At minimum, the prospective company must have some proven record of good job done on previous assignments. For a good choice, the level of experience of staff also matters.
About the Author:
Read more about Using Electrical Infrared Inspection Is A Sure Way To Save Time And Money.
0 Comments